Monitor. Protect. Schedule. Control. Connect.
An intelligent monitoring, protection and control unit for panels. It watches the supply voltage, cuts the output when it goes over or under your set limits, and switches the load to a daily schedule, all set from an Android phone over Bluetooth.

Single phase or three phase
The same controller, timer and app in both. Choose the model that matches your supply.

100–310 V AC
Voltage monitoring with BLE control for single-phase loads.
- Continuous supply voltage monitoring
- Over- and under-voltage limits you set
- Pump sets, borewells, motors and machines

310–415 V AC
Independent R, Y and B monitoring with BLE control.
- Each phase measured and reported separately
- Over- and under-voltage limits per phase
- Agricultural pump sets, motors and drives
Protection first, then the schedule
Voltage is read, protection is checked, and only then are timer or manual commands applied. A live fault cannot be overridden by a normal ON command.
Watches the line
Supply voltage is measured continuously and reported live, with a Normal, Over or Under state on the display and in the app.
Trips before damage
If the supply stays above your limit for the protection period, the output is switched off.
Guards the motor
A sustained dip below your limit disconnects the load, the condition that burns out pump and motor windings.
Runs to your hours
One programmable schedule with its own enable, ON time and OFF time. Set it once from the app and the unit keeps it.
Keeps date and time
An on-board clock holds time and calendar for accurate switching. The app syncs it to your phone in one tap.
Switch it by hand
Turn the output ON or OFF from the app at any time and read back the live relay state. Protection stays armed.
Survives a power cut
Schedules, limits and settings are held in non-volatile memory and restored when supply returns.
Sleeps after five minutes
The display turns on at power-up, switches off after five minutes, and one press brings it back. The controller runs throughout.
Set it from your phone
No Wi-Fi router, no SIM card and no internet connection are needed. Once configured, the phone can be put away and the controller carries on by itself.
Scan
Open the app and list nearby KELL devices.
Connect
Select your device and the dashboard opens.
Monitor
Read live voltage, relay, timer and protection status.
Configure
Set the limits, protection delay, recovery and schedule.
Sync & go
Sync the clock, disconnect, and the unit runs unattended.
Specifications
| Single phase | Three phase | |
|---|---|---|
| Working voltage | 100–310 V AC, 50 Hz | 310–415 V AC, 50 Hz |
| Measurement | Supply line voltage, continuous | R, Y and B phase voltage, continuous and independent |
| Protection | Over- and under-voltage, settable limits, with protection delay and recovery | Over- and under-voltage, limits settable per phase, with protection delay and recovery |
| Output | Relay contact, 1 A rating, suitable for contactor coil switching | |
| Timer | One programmable schedule: enable, ON hour/minute, OFF hour/minute | |
| Clock | Real-time clock with calendar; time sync from the Android app | |
| Memory | Schedules, protection limits and parameters held in non-volatile memory | |
| Wireless | Bluetooth Low Energy (BLE); Android application. No Wi-Fi required | |
| Display | OLED, auto ON at power-up, 5-minute timeout, one-touch wake | |
| Controller | ESP32, field-upgradable firmware | |
| Mounting | DIN rail, 35 mm, with plug-in screw terminals | |
| Ambient | −10 °C to +45 °C | |
| Origin | Made in India | |
Any load that runs to fixed hours
Installation note: suitability for a given installation depends on the load rating, contactor arrangement and the applicable electrical standards. Installation and wiring by a licensed electrician only. Specifications subject to change without notice.
Enquiries & orders
Manufactured in Kottayam, Kerala. OEM supply and panel-builder pricing on request.
+91 70340 11126 · sales@kell.co.in
+91 4828 2743 35/37
info@kell.co.in