Timer & protection system · Made in India

Monitor. Protect. Schedule. Control. Connect.

An intelligent monitoring, protection and control unit for panels. It watches the supply voltage, cuts the output when it goes over or under your set limits, and switches the load to a daily schedule, all set from an Android phone over Bluetooth.

KELL NEXTIMER three phase timer and protection unit
1 ARelay rating
35 mmDIN rail mounting
−10…45 °CAmbient
BLEAndroid app control
Two models

Single phase or three phase

The same controller, timer and app in both. Choose the model that matches your supply.

KELL NEXTIMER single phase
SINGLE PHASE

100–310 V AC

Voltage monitoring with BLE control for single-phase loads.

  • Continuous supply voltage monitoring
  • Over- and under-voltage limits you set
  • Pump sets, borewells, motors and machines
KELL NEXTIMER three phase
THREE PHASE

310–415 V AC

Independent R, Y and B monitoring with BLE control.

  • Each phase measured and reported separately
  • Over- and under-voltage limits per phase
  • Agricultural pump sets, motors and drives
What it does

Protection first, then the schedule

Voltage is read, protection is checked, and only then are timer or manual commands applied. A live fault cannot be overridden by a normal ON command.

Voltage sensing

Watches the line

Supply voltage is measured continuously and reported live, with a Normal, Over or Under state on the display and in the app.

Over-voltage

Trips before damage

If the supply stays above your limit for the protection period, the output is switched off.

Under-voltage

Guards the motor

A sustained dip below your limit disconnects the load, the condition that burns out pump and motor windings.

Timer schedule

Runs to your hours

One programmable schedule with its own enable, ON time and OFF time. Set it once from the app and the unit keeps it.

Real-time clock

Keeps date and time

An on-board clock holds time and calendar for accurate switching. The app syncs it to your phone in one tap.

Manual override

Switch it by hand

Turn the output ON or OFF from the app at any time and read back the live relay state. Protection stays armed.

Memory

Survives a power cut

Schedules, limits and settings are held in non-volatile memory and restored when supply returns.

Smart OLED

Sleeps after five minutes

The display turns on at power-up, switches off after five minutes, and one press brings it back. The controller runs throughout.

Android app · Bluetooth Low Energy

Set it from your phone

No Wi-Fi router, no SIM card and no internet connection are needed. Once configured, the phone can be put away and the controller carries on by itself.

01

Scan

Open the app and list nearby KELL devices.

02

Connect

Select your device and the dashboard opens.

03

Monitor

Read live voltage, relay, timer and protection status.

04

Configure

Set the limits, protection delay, recovery and schedule.

05

Sync & go

Sync the clock, disconnect, and the unit runs unattended.

Technical data

Specifications

Single phaseThree phase
Working voltage100–310 V AC, 50 Hz310–415 V AC, 50 Hz
MeasurementSupply line voltage, continuousR, Y and B phase voltage, continuous and independent
ProtectionOver- and under-voltage, settable limits, with protection delay and recoveryOver- and under-voltage, limits settable per phase, with protection delay and recovery
OutputRelay contact, 1 A rating, suitable for contactor coil switching
TimerOne programmable schedule: enable, ON hour/minute, OFF hour/minute
ClockReal-time clock with calendar; time sync from the Android app
MemorySchedules, protection limits and parameters held in non-volatile memory
WirelessBluetooth Low Energy (BLE); Android application. No Wi-Fi required
DisplayOLED, auto ON at power-up, 5-minute timeout, one-touch wake
ControllerESP32, field-upgradable firmware
MountingDIN rail, 35 mm, with plug-in screw terminals
Ambient−10 °C to +45 °C
OriginMade in India
Typical applications

Any load that runs to fixed hours

Pump sets and borewellsWater pumping and overhead tank systemsSingle- and three-phase motorsElectrical control and automation panelsSmall industrial machineryCommercial and facility equipmentScheduled lighting and utility loads

Installation note: suitability for a given installation depends on the load rating, contactor arrangement and the applicable electrical standards. Installation and wiring by a licensed electrician only. Specifications subject to change without notice.

Enquiries & orders

Manufactured in Kottayam, Kerala. OEM supply and panel-builder pricing on request.
+91 70340 11126  ·  sales@kell.co.in